|
| |
http://pesn.com/2007/01/08/9500445_Bob_Boyce_Electrolyzer_Plans/
You are here: PureEnergySystems.com
> News > January
8, 2007 |
|
Bob Boyce's Electrolyzer Plans Available to All
A system for high-efficiency electrolysis that involves the alleged
production of monatomic hydrogen, which has highly unusual and effective
properties in accentuating mileage.
by Michael Couch
for Pure Energy Systems News
 |
|
|
Bob Boyce was winning races in mini power boats down in Florida, using Hydrogen
for fuel. The problem was that hydrogen wasn't easy to locate and acquire
everywhere he raced. So, he began to research making his own.
Eventually he ended up making his own Hydroxy on demand in what might be called
the "brute force method". He'd drain his batteries producing the
Hydroxy that fed his engines.
One day he started noticing that at a certain RPM his power kicked up suddenly;
as though he had a nitro boost or something. After a few recurrences of this, he
broke down his system to find out what was causing his boost at that rpm.
It turned out that one of the diodes in his Alternator had failed and was
pumping an AC into his electrolyzer. When that certain rpm was reached the
output from the electrolyzer suddenly increased.
Researching further by having the gas analyzed at a local college, he found that
when the frequencies kicked in he was producing much more monatomic hydrogen. He
went on to perfect his electrolysis to the point that it generates a large
volume of gas and mostly monatomic hydrogen.
PVC Pipes running to his special bubbler are 1 inch in diameter to handle the
large gas flow required for big genset and auto operation. The electrolyzer cell
itself is either 61 plates for torches and small motors; or 81 plates for larger
gensets, boats and autos. Each cell is isolated from the others in that they are
not connected by the water and electrolyte (KOH 28% or NaOH 20%).
Today, though Bob has gotten out of boat racing, he makes his own PWM3
Controller for Hydroxy torches and gensets. They aren't for sale but you can
find the info in files on the Web. The controller uses three 556 Dual 555
timers. Each dual uses one 555 for pulse width and the other for frequency,
generating 42,800; 21,400; and 10,700 cps respectively.
These frequencies drive the 25% modulation on top of the pulsed DC carrier
"bias" current. The DC Bias voltage is input at the Toroidal
Transformer's inputs which gets filtered into DC before reaching the plates of
his electrolyzer with the AC Voltage riding on it.
It isn't critical how you get the pulses used to modulate the AC on the DC bias;
any method will do. A pressure switch is needed to turn the cell off at 5 psi
and back on when it falls to 3 psi. Bobs bubbler's have one way valves to retain
pressure in the system so that production begins immediately when the system
kicks back on. He uses many small holes in his bubbler inlet below the water so
bubbles are tiny and diffused. This is to prevent a flashback from firing across
several large bubbles back to the cell. Bob said it works well.
Plates are crosshatch sanded using no.80 sandpaper to create masses of points on
each plate surface. Plate edges are seal for two reasons; to prevent all the
separation from occurring only on the edges, and to prevent current leaking
through the water from cell to cell.
Bob says this causes a magnetic circuit through the center of the plates in the
electrolyzer. The result of all these refinements is that when the water is
split, the bias voltage keeps it from recombining, and H molecules have plenty
of electrons to absorb, preventing the two Hs from joining. Thus the extra large
volume of monatomic Hydrogen molecules.
Water must be distilled; or clean, spring or rainwater. These last may require
several filterings, to remove sludge; much like Joe
Cell Charging water. The 6"x6" Plates are spaced 3mm apart exactly
and sealed on the sides and bottom. Water levels must be maintained in each
cell. Bob's has a supply pipe with holes drilled along it for each cell.
If your system is designed according to all the specifications of the Boyce
system, Bob says, you will get another area of separation in the water between
the cells as well as on the plates.
Mr. Boyce is a true humanitarian and has placed his system in the public domain
in the hopes of helping the planet reverse global warming, end oil wars, and
deliver free energy to the poor peoples of the world.
Someday, Mr. Bob Boyce will be hailed as a truly great American Inventor. Bob
won't care for that; but hopefully the one who deserves the credit for his
accomplishments will get it. He expressed unhappiness with several people who he
tutored in Hydroxy production because they went on to patent or rather try to
patent systems that were largely based on information that he has placed in the
public domain.
# # #
Related Coverage
- New Release of OU Electrolyzer Plans
- Bob Boyce is one of the world's leading super-efficient electrolysis experts. A group of hydroxy researchers have compiled an updated set of
plans including
Toroidal Coil winding and hookup info enabling others to replicate the work of Boyce.
(PESN; September 29, 2007)
|
See also
|
|
|
Page posted by Sterling
D. Allan Jan. 8, 2007
Last updated December 06, 2007
|
| |
|
Feed